Delica Canada | Mitsubishi Van Club

Okay. I have the door panel off. But now that I have the door off, I’m trying to figuring out the wiring part of the job.

I bought a kit with 4 actuators. Obviously I don’t need that. In fact, I only need one. I’m not going to wire the rear hatch on this thing. And I don’t really care about the...

TL;DR: Rancho part number RS999188 adjustable shocks fit L300 front suspension, but require a touch of modification to do so safely. On their hardest setting they aren't as hard as I expected, but still show a clear improvement in handling on the road. Softest is like driving a bouncy castle and...

My window vents/louvers for my L300 arrived today and they fit great! I have two of them and plan on putting them one on each side of the van - this should allow me some great cross breezes while camping. The vents came with a mosquito net back - Great for Yukon summers!

My work on the van...

Thanks in advance for any advice or guidance:

I’m going to replace the stereo head on my 93 L300. I want to put one in that has the following features:

1) back up camera
2) fits well
3) easy to use and connect with iPhone
4) easy interface

Any must-have features you think I’m missing?

Any...

I've just bought a 1998 L400 high-roof Super Exceed. I grew impatient waiting for an LWB and finally went for a short wheel base that my wife and I plan to camperize as time, ability and money permits. I eventually plan to install a small fridge (Engel, Arb, Dometic, etc...) once I get a second...

Looking for some guidance in tapping the fuel line in an L300 to provide fuel to an Espar D2 air heater clone.

Can I directly break into the existing fuel line and butt a 'T' into it rather than tapping a tube directly into the fuel tank?

The rear springs on my Delica have sagged (as they all do) to the point where they were sitting on the overload leaves, which makes the ride quite harsh.

I've tried adding a leaf ( ) which made the ride smooth again when loaded, but it also raised the rear too far when the van was empty....

After fitting air shocks to the rear of my van, which slightly stiffen the rear suspension, I've been thinking that the front suspension is way too soft.

The Japanese market L300 4WD wagon (P25/35W) has 20mm diameter torsion bars on the front suspension. Light springs like these make for a...

My van should be in my drive next week and one of the first mods I want to complete is an install of EGT. I'm asking what you guys have used, what you prefer? Do you have pictures of your installation?

Sent from my Nexus 6P using Tapatalk

Went a little overboard on the awning. This is a 10'1" awning, projects 8'2". I used the brackets KIT VW T3. Worked good, just had to modify the small Z shaped bracket into a longer L shaped bracket. Waiting on some nutserts so I can wall mount it to the Delica. And it will eventually...

My L300 Exceed came pretty bare bones from the previous owner, and is missing all decals. I really like the stock look, so I would love to replace them. I do have a vinyl cutter, so making them up should be easy, but I would need templates. Does anyone have digital versions (Illustrator or any...

Hi guys/gals.

1) I'm wanting to insulate my 1999 L300 Delica low roof TD. How do I go about this? I've bust a couple round plastic clips (that I'm not sure how to replace) and feel I'm going to eff things up royally without some advice. The roof/ceiling seems particularly difficult.

2) How do I...

Well it took all day and a ton of work. I also learned do not use dupli color water based bed liner spray. It is very finicky and likes to run unless you spray extra extra light. But the run will be covered with a piece of stainless to mount LED's to.
I still have to raise the trans and AC cooler...

Earlier this year I installed an EGT gauge. It's been great for the anxiety, I monitor it fairly closely, stays between 400C and 550C on the highway and 700C on the bigger hills.

But, today, I'm sitting at a traffic light and glance over to see 1300C!!! and it's flashing and HOLY S**T!!! I pulled...

I'm getting a front skid made, using the drawing from this page...

Thinking we'll do a run of 8 of them, if anyone is interested let me know, and what kind of transmission, AT or Manual. also if anyone has input on what material, alu vs steel, and what thickness you'd want, hopefully we can use...

I’ve tried searching but can’t seem to find this simple info.

‘93 L300
Trying to decide (via pics and info) what to do for rims and tires and lift.
Simple question really: what size fits on stock suspensio with 15” rims and with 16” rims, and what does that look like. What size fits on the...