Air adjustable shock absorbers

User avatar
Growlerbearnz
Posts: 1653
Joined: Sat Jun 26, 2010 1:58 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica P25W
Location: New Zealand

Air adjustable shock absorbers

Postby Growlerbearnz » Wed Jan 17, 2018 4:08 pm

The rear springs on my Delica have sagged (as they all do) to the point where they were sitting on the overload leaves, which makes the ride quite harsh.

I've tried adding a leaf (http://www.delica.ca/forum/viewtopic.php?f=10&t=18521&p=137471&hilit=add+a+leaf#p137471) which made the ride smooth again when loaded, but it also raised the rear too far when the van was empty. ("Too far" meaning it wouldn't fit through the garage door without letting all the air out of the tyres).

So I've removed the add-a-leafs and gone for an old-school solution- air adjustable shock absorbers.

Monroe MA708.
MA708.JPG
MA708.JPG (50.47 KiB) Viewed 559 times

(http://www.monroe.com/en-US/e-catalog/MA708/) US$70 from Amazon.

Allegedly the same compressed and extended length as my Pro-Comp 919520's (https://www.procompusa.com/eSearch.aspx?Ntk=primary&Ntt=919520) but I think they're measuring from different points, because these clearly have a *lot* more droop than the Pro-Comps. They're also slightly longer when compressed, presumably because they have internal bump stops, but by my measurements they shouldn't bottom out (and the internal bump stops should prevent any damage if they do).

MonroeMA708.JPG
MonroeMA708.JPG (89.91 KiB) Viewed 559 times


They require a touch of modification. Remove the upper pin mount:
MonroePin.jpg
MonroePin.jpg (70.07 KiB) Viewed 559 times


...and install the bush from your old shocks:
MonroeFixed.JPG
MonroeFixed.JPG (100.09 KiB) Viewed 559 times


Then you get excited and install them without taking any further photos. Sorry.

They work brilliantly so far. Just 30psi brings the rear end back up to standard height, lifting the tired springs off the overload leaves, and restores the smooth ride. With the caravan hitched up and a bunch of junk in the van it required 70psi to come back to standard ride height, and it tows without any wallow or pitching.

Monroe recommend 20-90psi continuously (so I'm well within the specs), or up to 150psi for short periods. Air shocks have a reputation for overloading the shock mount points when used on regular cars, but I figure our beefed-up 4WD mounts can handle it. (Or watch this space for a thread titled "Shock absorber mount point repair and strengthening".)
Nothing says "poor workmanship" more than wrinkles in the duct tape.

definingdigital
Posts: 37
Joined: Sat Dec 17, 2011 7:07 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica
Location: Victoria, BC

Air adjustable shock absorbers

Postby definingdigital » Sun Jan 28, 2018 4:56 pm

Hey There,
I'm kind of running into the same issue. I was gonna add another leaf or get new leaf springs built.. but I was wondering if there was an airbag or air shock option. What do you use to pump it up? just a air hose or do you have a compressor on the vehicle?

How's it working still?

User avatar
Growlerbearnz
Posts: 1653
Joined: Sat Jun 26, 2010 1:58 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica P25W
Location: New Zealand

Air adjustable shock absorbers

Postby Growlerbearnz » Sun Jan 28, 2018 10:10 pm

I just use an air hose. The shocks have an air line kit with a tee that ends in a regular Schrader (tyre) valve.

valve.JPG
valve.JPG (38.42 KiB) Viewed 471 times
Tee.JPG
Tee.JPG (58.63 KiB) Viewed 471 times
RHS2.JPG
RHS2.JPG (63.75 KiB) Viewed 471 times
RHS.JPG
RHS.JPG (74.54 KiB) Viewed 471 times


I have a compressor in the van, but it's a tiny emergency one. I could use it to inflate the shocks if something went wrong, I guess.

So far so good. I've just finished 1200km driving towing the caravan and they've performed perfectly, with no squeaks or unexpected deflations. I left the pressure at 70psi when driving to the shops while camping (to avoid having to re-inflate the shocks later), and the van drove just fine, it just sits a little higher in the back than it should.
Nothing says "poor workmanship" more than wrinkles in the duct tape.

definingdigital
Posts: 37
Joined: Sat Dec 17, 2011 7:07 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica
Location: Victoria, BC

Air adjustable shock absorbers

Postby definingdigital » Sun Feb 04, 2018 2:46 pm

Looks great! Thanks for the updates! I'm gonna try it out.


Return to “Accessories, Modifications & Ideas”

Who is online

Users browsing this forum: No registered users and 0 guests