Dual piston slider pins.

Does your Mitsubishi L300 make a strange noise? Need wheel alignment specs?
Post Reply
User avatar
north54
Posts: 194
Joined: Tue Oct 01, 2013 10:29 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 1989 P35W
Location: Vancouver

Dual piston slider pins.

Post by north54 »

After a year and a half I feel like my front right brake caliper is failing. The slider pins are getting more and more corroded. I've already removed them, cleaned (sanded) them, regreased, installed about 3 times over 12 months. Whats odd is this is only happening on the front right, lefts are just fine.

I'm running dual piston on my L300.

Besides the corrosion I noticed both top and bottom pins on either side have the rubber grommet on the end. From what I've read there is supposed to be a pin with no rubber on top and a pin with the rubber grommet on the bottom. Can anyone confirm this? I'm running Beck Arnley Brake callipers. Thanks.
TRUSTY RUSTY
User avatar
Growlerbearnz
Posts: 2041
Joined: Sat Jun 26, 2010 1:58 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica P25W
Location: New Zealand

Dual piston slider pins.

Post by Growlerbearnz »

MB618227 top pin (plain pin). CAD$11 from Amayama.com
MB618227.jpg
MB618227.jpg (78.95 KiB) Viewed 4866 times
MB618228 lower pin (with rubber tip) CAD$10
MB618228.jpg
MB618228.jpg (8.72 KiB) Viewed 4866 times
The lower pin is supplied without the rubber. To get the rubber you need rebuild kit MB857840 (superseded by 4605B977 CAD$30)
MB857840.jpg
MB857840.jpg (25.67 KiB) Viewed 4866 times
To rebuild both sides you'd need 2 of each part number. The rebuild kit comes with all seals and the magic special grease that stops the pins from seizing for at least 30,000km. <--Sarcasm! but the genuine grease does seem to work better than regular grease.)

Normal petroleum based wheel bearing style grease doesn't seem to work very well or last very long. If you're determined to keep your old pins and rubber parts, I'd clean them out thoroughly, degrease them with a diesely rag and let them dry, clean out the tubes/holes on the calipers, and try reinstalling everything with silicone grease. Synthetic grease might also work.
Nothing says "poor workmanship" more than wrinkles in the duct tape.
User avatar
north54
Posts: 194
Joined: Tue Oct 01, 2013 10:29 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 1989 P35W
Location: Vancouver

Dual piston slider pins.

Post by north54 »

Thanks Growler. I'm not running genuine Mitsubishi calipers so not sure the OEM rebuild kit will work. Maybe I'll have to get some used OEM calipers and rebuild them.
TRUSTY RUSTY
User avatar
Growlerbearnz
Posts: 2041
Joined: Sat Jun 26, 2010 1:58 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica P25W
Location: New Zealand

Dual piston slider pins.

Post by Growlerbearnz »

Wow, so the new Beck Arnley slider pins are corroding after only a year and a half? That sounds like crappy quality.

Interesting that it's only happening on one side. How did you find out that they were corroding? Random precautionary inspection, or did one side seize up? If it seized up, maybe check that both pistons are moving freely- open the bleeder and push both pistons into their bores, then close the bleeder and pump the brake pedal to push them back out (topping up the reservoir as needed). If one piston sticks it tilts the caliper and jams the sliding pins.

Are the pads wearing the same on both sides? If the right side is wearing unevenly (thinner on one end) you've got a sticky piston.

Could you swap the pins from left to right and see if the issue swaps sides?
Nothing says "poor workmanship" more than wrinkles in the duct tape.
User avatar
north54
Posts: 194
Joined: Tue Oct 01, 2013 10:29 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 1989 P35W
Location: Vancouver

Dual piston slider pins.

Post by north54 »

I think I started to look into it because it was hard to stop the van. More pressure needed on the pedal than I recall. I upgraded to dual piston to make it easier. I think I'll have to replace the right caliper as the slider pins are so pitted they are making reinstall hard. Maybe I didn't install one of the little rubber bellows correctly and water got in. Insides must be corroded as well. Pads look ok.
TRUSTY RUSTY
User avatar
north54
Posts: 194
Joined: Tue Oct 01, 2013 10:29 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 1989 P35W
Location: Vancouver

Dual piston slider pins.

Post by north54 »

Had time to revisit this today and took apart the right front caliper. Pistons are good, nice and shiny and seem to slide well. One of the piston boots was bulging out for some reason before I took them apart. I was afraid it would be pinched when it touched the brake pad. After refitting everything they seem to seat better. Pins are still corroded so I'll replace them asap.
TRUSTY RUSTY
Post Reply

Return to “L300 Technical”