Removing Washer Jets

Locked
pj_jazzy_janz
Posts: 113
Joined: Wed May 21, 2014 7:28 am
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: '94 L400 LWB
Location: Winnipeg, MB

Removing Washer Jets

Post by pj_jazzy_janz »

Went poking around in there the other day (trying to angle the driver side a bit higher), but can't seem to get at the underside of the jets. Does anyone know the trick?
Ralph in Winnipeg
Posts: 239
Joined: Wed Sep 02, 2015 7:42 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 94 Strada
Location: Winnipeg

Trying to Remove Washer Jets

Post by Ralph in Winnipeg »

I'm pretty sure that you can angle the jets without removing them. I usually use a push pin (like on a bulletin board) and stick it it the nozzle to move it around. Ralph in Winnipeg.
pj_jazzy_janz
Posts: 113
Joined: Wed May 21, 2014 7:28 am
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: '94 L400 LWB
Location: Winnipeg, MB

Trying to Remove Washer Jets

Post by pj_jazzy_janz »

I'd heard that. I tried to jiggle some kind of pin in there, but it clearly lacked the required fortitude and broke off in the nozzle. :shock: Much cursing ensued. Now I need to get it out. I just can't figure out how to get at the underside of the jet.
User avatar
patriceboivin
Posts: 226
Joined: Fri Jan 03, 2014 1:45 pm
Member's Photo Album: http://www.delica.ca/Photos/index.php?cat=23122
Vehicle: Mitsubishi Delica L400 Super Exceed
Location: Canada
Location: Dartmouth, NS

Trying to Remove Washer Jets

Post by patriceboivin »

Probably won't work, but how about using a magnet to tease it back out?
izack98
Posts: 138
Joined: Tue Apr 30, 2013 4:15 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 1997 L400 Super Exceed PE8W
Location: Delta B.C.

Trying to Remove Washer Jets

Post by izack98 »

I had to remove my jets today to clean them. Here are some pics and a tutorial for you pj_jazzy_janz

First open the hood and remove all the bolts holding the cabin fresh air intake to the underside of the hood (I believe there were 16 screws/bolts altogether - not all are indicated in this pic).
Also remove the 3 grommets holding the rubber boot for the turbo fresh air inlet (one is circled in yellow).
There is also a row of bolts on the underside (area is indicated by the arrows)
IMG_1180.JPG
IMG_1180.JPG (475.42 KiB) Viewed 12246 times
Heres what the 10mm bolts look like. There are also 6 phillips screws.
IMG_1181.JPG
IMG_1181.JPG (390.07 KiB) Viewed 12246 times
Once you get the fresh air intake off you will see the hoses and nozzle locations. You may be able to work from here. I disconnected the hoses and blew compressed air back from the nozzles. Then blew out the lines. That cleared them out.
IMG_1173.JPG
IMG_1173.JPG (487.08 KiB) Viewed 12246 times
Last time I fixed them I had to remove the cowling (for lack of a better description). from the top side of the hood. Be careful as there are two snap in connectors on each side underneath. They are pretty brittle. I broke the first one as I didn't know they were there, then tried very carefully to remove the second one. It broke too. Arrows show the approximate location of these snap in connectors. Be patient. Both mine are broken but the cowling still stays on as there are several other push in connectors (different type) as well. So if/when you break those 2 outside ones there are others that will do the job.
IMG_1183.JPG
IMG_1183.JPG (408.24 KiB) Viewed 12246 times
This is how and where they push in to the hole in the hood (or used to).
IMG_1179.JPG
IMG_1179.JPG (476.11 KiB) Viewed 12246 times
Once you get the cowling off you will see the underside of the nozzles. Remove the hose and use needle nose pliers to gently squeeze together the retaining clips. The nozzle comes out easily.
IMG_1178.JPG
IMG_1178.JPG (385.45 KiB) Viewed 12246 times
I blew everything out with compressed air. Put it all back together and adjusted the nozzles.

I used a very tiny drill bit (used for cleaning carburetor jets etc) to play with the adjustment to get it just right. You have to be careful doing this or you will enlarge the sprayer hole and then it just dumps fluid at lower pressure at the bottom of the windshield.
IMG_1176.JPG
IMG_1176.JPG (488.68 KiB) Viewed 12246 times
Hope this helps.
izack98
Posts: 138
Joined: Tue Apr 30, 2013 4:15 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 1997 L400 Super Exceed PE8W
Location: Delta B.C.

Trying to Remove Washer Jets

Post by izack98 »

Oh yah, I should add.
If you just want to remove the nozzles you don't have to remove the fresh air ducting under the hood. It just makes it easier as it covers all the hoses and connectors to the nozzles.
It removes quite easily once all the screws are out.
thelazygreenfox
Posts: 901
Joined: Tue Jun 08, 2010 7:21 am
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 99 white Hi roof gas Chamonix
Location: Coquitlam B.C.
Location: coquitlam canada

Trying to Remove Washer Jets

Post by thelazygreenfox »

Good write up IZ. Gotta love pictures.
MD :-D
Wear your mask, it keeps others from seeing the parsley in your teeth
User avatar
Growlerbearnz
Posts: 2041
Joined: Sat Jun 26, 2010 1:58 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica P25W
Location: New Zealand

Trying to Remove Washer Jets

Post by Growlerbearnz »

Great work! This one's definitely going in the Technical Reference Library.
Nothing says "poor workmanship" more than wrinkles in the duct tape.
Locked

Return to “Body General”