L300 Head replacement and timing belt DIY, step by step

Does your Mitsubishi L300 make a strange noise? Need wheel alignment specs?
DexterH
Posts: 32
Joined: Tue Jul 07, 2015 7:27 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Mitsubishi L300
Location: Trinidad

Re: L300 Head replacement and timing belt DIY, step by step

Post by DexterH »

Hi Tojo. I was hoping to catch your reassembly and timing on this project, but it doesnt seem I will.
Well, not when I need it most that is. I have to admit this is the best instruction diy project on this topic Ive seen. The photos are exceptional as well. The thing is, Tomorrow morning Im hoping to get that crank bolt off and prepare for reassembly/timing. Got some cleaning up on the head to do and replacing the old rocker arm assembly with a new one. I doubt I'll complete this job by end of the day but hoping to get as much done as possible. Oh! I have to thank you for the pic on how you rigged up the breaker bar using the 2x4 :-). I took out my starter hoping to find a threaded bore on the flywheel to lock it in place but was surprised there wasnt any.
Your method has put a smile on my face man :-)

Hope you get going on this project again soon. It sure is extremely helpful and very comprehensive.

Thanks Tojo!
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

I'm back! Thanks for the comments. Needed to take a break to work on the house, rebuild a 1974 Husqvarna L65 and some chill out time in this heat wave we're having.

A very old but sturdy saw. Something about these older saws, they are heavy with all metal parts and don't have a safety brake, but they have great torque and are ideal for chainsaw milling.
IMG_20150504_134541.jpg
IMG_20150504_134541.jpg (480.46 KiB) Viewed 15717 times
But I digress. Now, onwards and upwards!

Water pump is Hyundai OEM.
IMG_20150421_090114.jpg
IMG_20150421_090114.jpg (367.92 KiB) Viewed 15717 times
Time to deal with the balancer belt. Remove the two bolts that hold the tensioner and remove it.
IMG_20150714_160658.jpg
IMG_20150714_160658.jpg (328.95 KiB) Viewed 15717 times
Pull off both crank gears. Here is a picture of the outer one which the timing belt goes around.
IMG_20150714_161455.jpg
IMG_20150714_161455.jpg (328.4 KiB) Viewed 15717 times
Note that there is a spacer between them where the convex profile faces outwards.
IMG_20150714_161528.jpg
IMG_20150714_161528.jpg (242.63 KiB) Viewed 15717 times
You can see that there is a bunch of oil around the crankshaft, so it's a good time to replace the seal.
IMG_20150714_161716.jpg
IMG_20150714_161716.jpg (385.88 KiB) Viewed 15717 times
Last edited by Tojo on Wed Jul 15, 2015 4:56 pm, edited 1 time in total.
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

I made my own balancer gear removal tool. Just two bolts with a larger hole in the middle for the socket.
IMG_20150714_162911.jpg
IMG_20150714_162911.jpg (279.26 KiB) Viewed 15717 times
IMG_20150714_162920.jpg
IMG_20150714_162920.jpg (253.47 KiB) Viewed 15717 times
Use the improvised tool and cranked the upper balancer shaft gear loose.
IMG_20150714_165136.jpg
IMG_20150714_165136.jpg (304.56 KiB) Viewed 15717 times
And this is what it looks like underneath.
IMG_20150714_165400.jpg
IMG_20150714_165400.jpg (388.91 KiB) Viewed 15717 times
Used the tool again to remove the lower balancer shaft gear.
IMG_20150714_165408.jpg
IMG_20150714_165408.jpg (354.79 KiB) Viewed 15717 times
Pull off the upper balance shaft bushing and remove the oil seal, then replace with new ones. The reason to do this is because a groove gets worn into the bushing over time and causes a slow leak. Even if you just replace the oil seal the chances of it leaking are high if you decide to re-use the old bushing. My philosophy with this entire rebuild is to replace everything critical because the reality is that the major cost is your time. The parts themselves are small and relatively cheap for the most part, except for the timing belt and water pump (and the head of course!).
IMG_20150715_133713.jpg
IMG_20150715_133713.jpg (316.26 KiB) Viewed 15717 times
Nice and shiny! Used a large socket to press in the new oil seal.
IMG_20150715_135342.jpg
IMG_20150715_135342.jpg (230.98 KiB) Viewed 15717 times
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

By the way. Use a small 1/16" drill bit to make holes in the oil seals then drive a tiny screw into the hole and use needlenose pliers (bentnose preferred) to remove the seal. Just don't drill into the shaft or aluminum housing!
IMG_20150715_135913.jpg
IMG_20150715_135913.jpg (302.61 KiB) Viewed 15714 times
Use the same method to remove the crank oil seal.
IMG_20150715_141420.jpg
IMG_20150715_141420.jpg (309.19 KiB) Viewed 15714 times
Pull out the oil pump drive gear sleeve. Again because of the worn in groove that lets oil past as well as the teeth can get worn out. In this case the gear teeth look fine, but whatever, I replace anyways.
IMG_20150715_141543.jpg
IMG_20150715_141543.jpg (350.72 KiB) Viewed 15714 times
New oil pump drive gear sleeve.
IMG_20150715_141656.jpg
IMG_20150715_141656.jpg (505.12 KiB) Viewed 15714 times
An ABS fitting works really well for press fitting that crank oil seal. 2" to 2.25" outer diameter sleeve is what you're looking for.
IMG_20150715_142417.jpg
IMG_20150715_142417.jpg (397.37 KiB) Viewed 15714 times
Looking freshened up.
IMG_20150715_142833.jpg
IMG_20150715_142833.jpg (318.97 KiB) Viewed 15714 times
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

Replace the o-ring on the water pump outlet.
IMG_20150715_143132.jpg
IMG_20150715_143132.jpg (267.35 KiB) Viewed 15712 times
Look at the difference between the old and new. The old one was hard, brittle and flattened. New one is soft, pliable and rounded profile.
IMG_20150715_143240.jpg
IMG_20150715_143240.jpg (335.07 KiB) Viewed 15712 times
Done. Ready to install the water pump.
IMG_20150715_143306.jpg
IMG_20150715_143306.jpg (251.48 KiB) Viewed 15712 times
Attach the new balancer belt tensioner.
IMG_20150715_143429.jpg
IMG_20150715_143429.jpg (289.54 KiB) Viewed 15712 times
IMG_20150715_164905.jpg
IMG_20150715_164905.jpg (350.77 KiB) Viewed 15712 times
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

Just to backtrack and highlight a few details.

On the upper balance shaft bushing the chamfered edge faces inwards.
IMG_20150717_145025.jpg
IMG_20150717_145025.jpg (264.85 KiB) Viewed 15692 times
Knock out the woodruff key with a flathead screwdriver bit and place in a new one. Makes for a nice snug fit with the crank sprockets.
IMG_20150717_145931.jpg
IMG_20150717_145931.jpg (242.27 KiB) Viewed 15692 times
IMG_20150717_150450.jpg
IMG_20150717_150450.jpg (290.91 KiB) Viewed 15692 times
Next it was time to place the balancer belt. AKA timing belt "B"
Use a lever bar to push against the tensioner spring and turn the bolts to hold the tensioner in place.
IMG_20150717_152923.jpg
IMG_20150717_152923.jpg (299.88 KiB) Viewed 15692 times
Align all the timing marks on each sprocket and slip the balancer belt into place. It took a couple of tries to get it to line up.
IMG_20150717_153352.jpg
IMG_20150717_153352.jpg (244.71 KiB) Viewed 15692 times
Release the tensioner and check for deflection on the right side which should be 4 to 5 mm according to the manual. Note that the belt has direction. This is a clockwise turning motor.
IMG_20150717_153339.jpg
IMG_20150717_153339.jpg (348.87 KiB) Viewed 15692 times
Last edited by Tojo on Fri Jul 24, 2015 5:23 pm, edited 2 times in total.
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

On goes the water pump. Straightforward, but watch that you get the correct bolts of the correct grade stamped on the head into the correct hole! See the attached diagram. I used some Permatex RTV gasket maker to stick it all together.
IMG_20150717_155953.jpg
IMG_20150717_155953.jpg (277.89 KiB) Viewed 15692 times
IMG_20150717_161405.jpg
IMG_20150717_161405.jpg (225.04 KiB) Viewed 15692 times
water pump_sm.jpg
water pump_sm.jpg (107.15 KiB) Viewed 15692 times
Last edited by Tojo on Sun Jul 26, 2015 9:06 pm, edited 2 times in total.
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

Fresh dowels on the block.
IMG_20150721_132448.jpg
IMG_20150721_132448.jpg (307.26 KiB) Viewed 15692 times
Clean the mating surfaces with brake cleaner because it evaporates and leaves no residue. Then place the head gasket. Used compressed air to blow out the head bolt holes and clean off the threads in the block.
IMG_20150721_133309.jpg
IMG_20150721_133309.jpg (282.55 KiB) Viewed 15692 times
On goes the head.
IMG_20150721_144523.jpg
IMG_20150721_144523.jpg (399.7 KiB) Viewed 15692 times
Take your time and torque to spec which is 113-123 Nm or 83 to 90 ft. lbs. Follow the pattern. Do it gradually and work your way around the pattern several times before reaching your final torque setting.
head bolt install.JPG
head bolt install.JPG (56.68 KiB) Viewed 15692 times
Fresh head bolts. Chamfered edge on the washer faces up. I used a small drop of engine oil on the threads. Not too much or it leads to hydraulic lock and stripped threads.
IMG_20150721_135857.jpg
IMG_20150721_135857.jpg (359.45 KiB) Viewed 15692 times
Ready to start reattaching stuff!
IMG_20150721_141103.jpg
IMG_20150721_141103.jpg (379.21 KiB) Viewed 15692 times
Last edited by Tojo on Sun Jul 26, 2015 9:06 pm, edited 1 time in total.
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

Timing belt time!

On goes the new tensioner.
IMG_20150722_094327.jpg
IMG_20150722_094327.jpg (266.5 KiB) Viewed 15678 times
Tricky to get the tensioner and spring into place. Probably a few ways to do this, and this is what I did. Place a small lever bar and push against the spring (towards the drivers side). Pop the spring over the bent metal hook on the tensioner.
IMG_20150722_095313.jpg
IMG_20150722_095313.jpg (275.19 KiB) Viewed 15678 times
Once the spring is in place and you've replaced the two bolts, move the lever bar to this position on the tensioner and apply some leverage to push against the spring. Tighten the upper bolt on the tensioner to hold it in place so it doesn't rebound. Keep the bottom bolt finger tight.
IMG_20150722_100019.jpg
IMG_20150722_100019.jpg (250.29 KiB) Viewed 15678 times
Align all the marks on the crank, cam and IP sprockets. Clamp the belt in place on the crank sprocket.
IMG_20150722_120329.jpg
IMG_20150722_120329.jpg (325.3 KiB) Viewed 15678 times
Put a wrench on the IP sprocket and turn it clockwise to align the timing mark, then clamp on the timing belt. There will now be slight tension on the right side of the belt (passenger side).
IMG_20150722_120354.jpg
IMG_20150722_120354.jpg (338.44 KiB) Viewed 15678 times
Ease the belt onto the cam sprocket without moving anything and it should look like this.
IMG_20150722_120648.jpg
IMG_20150722_120648.jpg (755.41 KiB) Viewed 15678 times
Release the upper bolt on the tensioner and allow the spring to apply tension to the belt. Torque both bolts down and you're done!
Check deflection, should be 4 to 5 mm.
IMG_20150722_121109.jpg
IMG_20150722_121109.jpg (263.02 KiB) Viewed 15678 times
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
lrp374
Posts: 1023
Joined: Sun Nov 23, 2008 9:56 pm
Vehicle: 91 Super Exceed
Location: Kamloops

Re: L300 Head replacement and timing belt DIY, step by step

Post by lrp374 »

Tojo I just reviewed your post on the Head replacement etc. and it even makes more sense than the first time. I didn't remember the replacement section but it will even be more help than the removal. I think you should get some kind of award or @ least a royalty from those who use your great post. Thanks again for the effort I know it really adds a lot of time to your repair. :-D
User avatar
ChuckBlack
Posts: 333
Joined: Tue Mar 17, 2015 9:27 pm
Member's Photo Album: http://www.delica.ca/Photos/Bingo
Vehicle: L300 Jasper
Location: St. Albert AB

Re: L300 Head replacement and timing belt DIY, step by step

Post by ChuckBlack »

Excellent! Great work!
L300 Jasper, :-D
L300 Chamonix, :-)
Pajero Mini, :-(
Pajero GDI :o
Pajero DiD 8-)
User avatar
Matt&Kim
Posts: 28
Joined: Sun Nov 04, 2012 11:12 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: '91 Delica L300
Location: Terrace, BC

L300 Head replacement and timing belt DIY, step by step

Post by Matt&Kim »

Hey guys, I'll be looking to replace my head gasket soon as it's pooched, just curious if it's entirely necessary to replace the head bolts when I do it.

Thanks!
Walking gingerly across the bruised earth.
User avatar
FalcoColumbarius
Site Admin
Posts: 5983
Joined: Tue Jan 22, 2008 1:55 pm
Member's Photo Album: http://www.delica.ca/Photos/index.php?cat=11103
Vehicle: Delica; Chamonix GLX ('92 P25W)
Location: North Van, BC, eh?

L300 Head replacement and timing belt DIY, step by step

Post by FalcoColumbarius »

Matt&Kim wrote:Hey guys, I'll be looking to replace my head gasket soon as it's pooched, just curious if it's entirely necessary to replace the head bolts when I do it.

Thanks!
On extra items, if you have, say, the lug nuts on your wheels ~ if you don't get the torque spot on ~ it's of small consequence, so long as you get it close. However, if you're dealing with the engine ~ you really need to be perfect. You need to appreciate that the engine is operating at an average of around 2,600 RPM at a 21:1 compression ratio. I would think the current head bolts would have stretched over time. How much would you save if you left the old bolts in ~ as compared to the engine's overall longevity and performance integrity? (Rhetorical)

Falco.
Sent from my smart pad, using a pen.

Seek Beauty... Image Good Ship Miss Lil' Bitchi

...... Vision without action is a daydream. Action without vision is a nightmare. ~ Japanese Proverb
User avatar
mcmastai
Posts: 22
Joined: Mon Jan 30, 2017 5:56 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: '93 L300 Chamonix
Location: Regina

L300 Head replacement and timing belt DIY, step by step

Post by mcmastai »

Hi everyone,

I just got finished installing my new T belt and other bits, everything is reinstalled - but the engine won't fire, it simply cranks. I know the obvious answer is the timing is off (tear it down again, bleh), but if none of the sprockets moved during installation how can that be? (Save the IP pump sprocket which rotated 360º back to its proper alignment).

Any suggestions before I dig back in would be great..

Thanks!
User avatar
weelsey
Posts: 73
Joined: Mon Nov 13, 2017 5:36 pm
Member's Photo Album: http://www.delica.ca/Photos/profile.php?uid=15295
Vehicle: '90 2.5l high roof exceed
Location: Harvey Parish, NB

L300 Head replacement and timing belt DIY, step by step

Post by weelsey »

This is awesome.. Thanks, Tojo! I hope my crank pulley removes so easily.

What do you all suppose is the difference in these belts besides the cost? Top two have images of the belt that have mitsubishi" stamped on them @
souq_Time.jpg
souq_Time.jpg (210.52 KiB) Viewed 13828 times
Post Reply

Return to “L300 Technical”