L300 Head replacement and timing belt DIY, step by step

Does your Mitsubishi L300 make a strange noise? Need wheel alignment specs?
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

Hello Delica.ca,

The head on the ol' L300 cracked about a year ago and I'm finally ready to tackle the job. My van is parked uncovered in the backyard, no hydraulic lift or air tools. Grungy backyard mechanic! I'll be doing the updates in real-time so it might take awhile. I'll endeavor to be as clear and concise as possible. Let me know if you have questions. Best to download the full service manual and refer to the torque specs there.

The following is a step by step head and timing belt replacement for a 4D56 2.5L turbo diesel as found in my 1993 L300 Delica Super Exceed. It has 140,000 kms on the clock and has had a pyrometer since it was imported in 2009 with 56,000 kms. Timing belts and water pump were replaced on import. It's pretty much stock except for EGR blanking plates, pyrometer, K&N filter and stainless 2.5" exhaust. Turbo cartridge was replaced as well as the turbo seals. This is the first time this motor has been torn down. I'll try to upload as many photos as I can and add as much detail as I can. I'm presuming that you have some basic mechanical knowledge, as well as good "feel". I find that this intuitive mechanical skill that some people have is very important when working on a motor. Knowing when to use force, and knowing when to back off before shearing a bolt is the difference between success and frustration. Although I've wrenched on a lot of vehicles, this is the first time I'm tackling this motor, so if there are constructive comments or suggestions from mechanics who have done this before, it would be appreciated.

Tool list (*will be updated as we go*):
- Metric socket set, 3/8" and 1/2" drive
- Metric impact sockets
- Closed end wrenches
- Ratcheting closed end wrenches
- Phillips screwdriver
- Flat head screwdriver
- Lever bars
- Breaker bars, 24" and 30", 1/2" drive
- Trays for collecting parts
- Trays for collection fluids
- Funnel
- Wire brushes
- Needlenose pliers
- Bent needlenose pliers
- Lineman's pliers
- Wire brushes
- Soft mallet
- Soft scraper
- Torque wrench
- Roloc bristle disc
- Cam/Crank removal tool

Supplies (*will be updated as we go*):
- Deep Creep penetrating oil or similar like Liquid Wrench
- Shop rags
- Nitrile gloves
- WD40
- Super Lube silicone grease
- Automotive solvent
- Degreaser
- Brake cleaner, aerosol can
Last edited by Tojo on Wed Jul 22, 2015 5:04 pm, edited 11 times in total.
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

Remove the drivers seat by following this excellent post: http://www.delica.ca/forum/drivers-side ... -2125.html

Then remove the centre console, there are two hidden phillips screws under the power window switches. I did this so it wouldn't get damaged when I remove the passenger seat.
IMG_20150302_104229.jpg
IMG_20150302_104229.jpg (119.59 KiB) Viewed 20539 times
Remove the bolts behind the passenger seat. Then remove the seat and engine cover. Don't forget to unplug the cable!
IMG_20150302_104421.jpg
IMG_20150302_104421.jpg (166.17 KiB) Viewed 20539 times
IMG_20150302_104432.jpg
IMG_20150302_104432.jpg (148.46 KiB) Viewed 20539 times
And now the engine compartment is opened up and ready to go.
IMG_20150302_113839.jpg
IMG_20150302_113839.jpg (301.28 KiB) Viewed 20539 times
Last edited by Tojo on Fri Mar 06, 2015 5:20 pm, edited 3 times in total.
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

Disconnect the battery
IMG_20150305_131740.jpg
IMG_20150305_131740.jpg (145.13 KiB) Viewed 20536 times
IMG_20150305_131943.jpg
IMG_20150305_131943.jpg (164.03 KiB) Viewed 20536 times
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

Remove upper radiator hose and coolant overflow hose.
IMG_20150305_132501.jpg
IMG_20150305_132501.jpg (129.02 KiB) Viewed 20534 times
Ratcheting closed end wrenches are handy here to get at the radiator hose clamps.
IMG_20150305_132744.jpg
IMG_20150305_132744.jpg (99.39 KiB) Viewed 20534 times
Remove clip for fan shroud by sliding rearward.
IMG_20150305_133115.jpg
IMG_20150305_133115.jpg (103.06 KiB) Viewed 20534 times
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

Remove the single bolt that holds the radiator. There is a metal spacer inside the rubber sleeve which I promptly dropped down onto the skidplate somewhere.
Will have to remember to locate that later.
IMG_20150305_133146.jpg
IMG_20150305_133146.jpg (131.83 KiB) Viewed 20534 times
IMG_20150305_135139.jpg
IMG_20150305_135139.jpg (144.32 KiB) Viewed 20534 times
IMG_20150305_135143.jpg
IMG_20150305_135143.jpg (140.26 KiB) Viewed 20534 times
This little bugger of a phillips screw was rusted on, so I cut it off. I'll replace it with a new one upon reassembly. It holds the fan shroud on. Now you can slide the other fan shroud off towards the drivers side.
IMG_20150305_133422.jpg
IMG_20150305_133422.jpg (96.94 KiB) Viewed 20534 times
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

Next I removed the radiator hose on the drivers side. It's difficult to access the bottom of the hose, so I just detached the top. Also, remove the rest of the fan shroud by undoing 4 bolts. Two are shown with arrows and two are hidden and are difficult to access as they are deep in there. Use a socket extension or long sockets.
IMG_20150305_140359.jpg
IMG_20150305_140359.jpg (146.57 KiB) Viewed 20524 times
Now you can remove the two hoses at the bottom of the radiator. This is where I used some penetrating oil and a wire brush to loosen up the seized clamp.
IMG_20150305_141625.jpg
IMG_20150305_141625.jpg (144.95 KiB) Viewed 20524 times
And once that's done, pull the radiator upward, carefully so you don't damage the fins. Nice to have a helper for this. You are left with an engine compartment that looks like this.
IMG_20150305_143748.jpg
IMG_20150305_143748.jpg (117.07 KiB) Viewed 20524 times
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

Decided to remove the inspection panel on the timing belt so I could see the condition. No oil, nice and dry with a bit of black dust. Could probably have pushed it but I'm replacing it after 80,000 kms which is on the safe side.
IMG_20150305_143936.jpg
IMG_20150305_143936.jpg (154.04 KiB) Viewed 20458 times
Took off the fan. Awkward but doable. Four bolts hold the fan onto the pulley. I've heard some mechanics call these belts "rubber Bando's" because they are supposed to stretch out.
IMG_20150305_144728.jpg
IMG_20150305_144728.jpg (101.35 KiB) Viewed 20458 times
IMG_20150305_144723.jpg
IMG_20150305_144723.jpg (114.75 KiB) Viewed 20458 times
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

Remove the fan, then loosen off the nut that threads onto the rod to tighten the belt tensioning pulley.
IMG_20150305_145250.jpg
IMG_20150305_145250.jpg (147.66 KiB) Viewed 20426 times
I decided the loosen up the 4 bolts that hold together the crank pulley. Still trying to decide how to remove the pulley as there are several ways to do it.
IMG_20150306_112636.jpg
IMG_20150306_112636.jpg (132.34 KiB) Viewed 20426 times
Loosen up the bolts that secure the alternator tensioning bracket.
IMG_20150306_113541.jpg
IMG_20150306_113541.jpg (163.47 KiB) Viewed 20426 times
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

Loosen off the bolts on either side of the power steering pump.
IMG_20150306_113811.jpg
IMG_20150306_113811.jpg (114.39 KiB) Viewed 20372 times
Hooking two closed end wrenches together like this gives more leverage in tight places and helps to crack this bolt. Mine was stubborn, used lots of penetrating oil and let it sit for awhile.
IMG_20150306_113922.jpg
IMG_20150306_113922.jpg (105.39 KiB) Viewed 20372 times
Now that all the belts are loose, remove them and mark them. Then remove the fan pulley which just slides right off.
IMG_20150306_134458.jpg
IMG_20150306_134458.jpg (118.79 KiB) Viewed 20372 times
Mark and remove the vacuum hose that crosses in front of the timing belt cover.
IMG_20150309_103150.jpg
IMG_20150309_103150.jpg (132.56 KiB) Viewed 20372 times
Loosen off the hidden nut and remove the tensioner pulley.
IMG_20150309_103801.jpg
IMG_20150309_103801.jpg (140.48 KiB) Viewed 20372 times
IMG_20150309_104559.jpg
IMG_20150309_104559.jpg (121.29 KiB) Viewed 20372 times
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

Remove the glow plug rail.
IMG_20150309_104808.jpg
IMG_20150309_104808.jpg (124.02 KiB) Viewed 20347 times
IMG_20150309_104818.jpg
IMG_20150309_104818.jpg (123.11 KiB) Viewed 20347 times
Make a note of where the wire attaches to the third glow plug.
IMG_20150309_105035.jpg
IMG_20150309_105035.jpg (144.14 KiB) Viewed 20347 times
IMG_20150309_105726.jpg
IMG_20150309_105726.jpg (125.73 KiB) Viewed 20347 times
Remove the two small hoses that attach to the turbo. Bent needlenose pliers work well for this.
IMG_20150309_105415.jpg
IMG_20150309_105415.jpg (124.84 KiB) Viewed 20347 times
IMG_20150309_105404.jpg
IMG_20150309_105404.jpg (116.16 KiB) Viewed 20347 times
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

Pull the power steering pump out of the way and wire it to the side of the engine compartment.
IMG_20150309_110426.jpg
IMG_20150309_110426.jpg (104.66 KiB) Viewed 20346 times
IMG_20150309_110532.jpg
IMG_20150309_110532.jpg (125.35 KiB) Viewed 20346 times
Remove the power steering bracket.
IMG_20150309_110616.jpg
IMG_20150309_110616.jpg (107.98 KiB) Viewed 20346 times
IMG_20150309_111016.jpg
IMG_20150309_111016.jpg (99.45 KiB) Viewed 20346 times
Then remove the second half of the power steering bracket attached to the head.
IMG_20150309_111016a.jpg
IMG_20150309_111016a.jpg (104.82 KiB) Viewed 20321 times
IMG_20150309_111016b.jpg
IMG_20150309_111016b.jpg (132.56 KiB) Viewed 20321 times
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

Remove the flexible and metal air intake hoses that lead to the turbo.
IMG_20150309_111057.jpg
IMG_20150309_111057.jpg (144.78 KiB) Viewed 20321 times
IMG_20150309_111342.jpg
IMG_20150309_111342.jpg (111.6 KiB) Viewed 20321 times
Detach the short hose that goes to the valve cover.
IMG_20150309_111508.jpg
IMG_20150309_111508.jpg (158.05 KiB) Viewed 20321 times
Starting to clear out the drivers side of the block, to eventually dig down to the intake and exhaust manifolds. Remove the other vacuum hose marked "B" in this photo that leads to the turbo.
Attachments
IMG_20150309_111704.jpg
IMG_20150309_111704.jpg (136.93 KiB) Viewed 20321 times
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

After you've removed the large flexible hose leading to the turbo, as well as the small vacuum hoses, reach in there and wiggle the axle of the turbine to check for excessive play. If there is too much play, then rebuild your turbo by replacing the seals and bushings, or replace the cartridge itself.
IMG_20150309_111910.jpg
IMG_20150309_111910.jpg (142.45 KiB) Viewed 20319 times
IMG_20150309_111950.jpg
IMG_20150309_111950.jpg (120.96 KiB) Viewed 20319 times
IMG_20150309_112005.jpg
IMG_20150309_112005.jpg (68.61 KiB) Viewed 20319 times
Remove the vacuum rail attached to the top of the valve cover.
IMG_20150309_112347.jpg
IMG_20150309_112347.jpg (171.48 KiB) Viewed 20319 times
IMG_20150309_112526.jpg
IMG_20150309_112526.jpg (163.55 KiB) Viewed 20319 times
IMG_20150309_112538.jpg
IMG_20150309_112538.jpg (143.94 KiB) Viewed 20319 times
Last edited by Tojo on Thu Mar 12, 2015 1:34 pm, edited 1 time in total.
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
Tojo
Posts: 185
Joined: Mon Oct 31, 2011 4:17 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L400 Super Exceed LWB
Location: West Kootenays, BC

Re: L300 Head replacement and timing belt DIY, step by step

Post by Tojo »

Remove the sheet metal heat sheild attached to the exhaust manifold. Mine was rusted on there, so I was patient, used lots of penetrating oil. Because the bolt head was getting rounded out, I ended up hammering on a smaller imperial sized 3/8" closed end wrench and cranking on it. Finally it cracked loose. Last resort would have been to use the torch and heat it up, but didn't have to this time.
IMG_20150311_164444.jpg
IMG_20150311_164444.jpg (123.46 KiB) Viewed 20317 times
IMG_20150311_164543.jpg
IMG_20150311_164543.jpg (132.84 KiB) Viewed 20317 times
Remove all the bolts and nuts for the intake and exhaust manifolds.
IMG_20150312_103030.jpg
IMG_20150312_103030.jpg (122.05 KiB) Viewed 20317 times
IMG_20150312_103037.jpg
IMG_20150312_103037.jpg (126.37 KiB) Viewed 20317 times
1993 Delica L300, SWB, LSD, Super Exceed with Crystal-Lite, mostly stock but it's got a digital EGT!!!
1995 Delica L400, LWB, Super Exceed with Crystal-lite, Airlift airbags, SS intercooler pipes, soon to be WVO
1997 Isuzu ELF 2.0Ton Crane truck, 4300cc diesel, NKR66E
User avatar
joebillhill
Posts: 163
Joined: Wed Apr 02, 2014 10:52 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 1989 Mitsubishi Delica l300
Location: United States

Re: L300 Head replacement and timing belt DIY, step by step

Post by joebillhill »

This is great Tojo! Very detailed and loads of pictures to help me and others along. Thanks!
Post Reply

Return to “L300 Technical”