Front skid plates for sale, interested?

Mitsubishi Delica Camper vans, lift kits & other Delica Accessories!

Moderator: BCDelica

jesseydearing
Posts: 8
Joined: Fri Jul 21, 2017 9:36 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 1991 L300 P35W Super Exceed
Location: Seattle
Location: Seattle, Washington

Front skid plates for sale, interested?

Post by jesseydearing »

Hey Mr. Sa,

Just checking in again to see if you were ever able to make those skid plates?

Cheers,

Jessey
1991 L300 P35W Super Exceed
User avatar
Crankshaft Culture
Posts: 85
Joined: Tue Jun 20, 2017 11:07 am
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 1989 Delica
Location: Portland, OR
Contact:

Front skid plates for sale, interested?

Post by Crankshaft Culture »

I bought one of these but cannot for the life of me figure out where it bolts up. I have an '89 L300 and have removed the two thin front guards from beneath my van. Does anyone have photos of one of these installed?
VE7LHM
Posts: 2
Joined: Sun Apr 07, 2013 9:59 am
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: L300
Location: Delta BC

Front skid plates for sale, interested?

Post by VE7LHM »

If not to late I would be interested I have a 91 Automatic.
Mr.SA
Posts: 59
Joined: Wed Mar 02, 2016 10:40 am
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L300
Location: Denver

Front skid plates for sale, interested?

Post by Mr.SA »

I'm out of them right now, I'm trying to come up with a different design thats a little easier to mount. I could do another run of these same styles if there is enough interest.
Mr.SA
Posts: 59
Joined: Wed Mar 02, 2016 10:40 am
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L300
Location: Denver

Front skid plates for sale, interested?

Post by Mr.SA »

If i can get much interest, I'll make another run of these, my friend that was doing them before is unable to now, but i know someone else that will be able to, might just cost me a little more.

After my last run, a few people had trouble mounting them. just be aware that it will take some bending/drilling on your part to fit them. and you NEED the undertray under the engine to mount them to.

If you're interested, post your material preference, steel or aluminum, and auto or manual trans. If i get a lot of interest in aluminum i'll do some, otherwise they'll be all steel.
I'll give it a couple weeks to guage interest, then make a run based on that. so we're looking at about a month timeframe.

I'm still planning on eventually doing a super strong version, but not until i can find someone that will work with me on building them. and those will cost quite a bit more than these.
bigsleep55
Posts: 13
Joined: Fri Jul 20, 2018 5:50 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: '92 L300 2.5TD
Location: Vancouver

Front skid plates for sale, interested?

Post by bigsleep55 »

Mr.SA wrote:If i can get much interest, I'll make another run of these, my friend that was doing them before is unable to now, but i know someone else that will be able to, might just cost me a little more.

After my last run, a few people had trouble mounting them. just be aware that it will take some bending/drilling on your part to fit them. and you NEED the undertray under the engine to mount them to.

If you're interested, post your material preference, steel or aluminum, and auto or manual trans. If i get a lot of interest in aluminum i'll do some, otherwise they'll be all steel.
I'll give it a couple weeks to guage interest, then make a run based on that. so we're looking at about a month timeframe.

I'm still planning on eventually doing a super strong version, but not until i can find someone that will work with me on building them. and those will cost quite a bit more than these.
How much do these end up costing with shipping to Ca? I'd be Aluminium for Auto. Thanks!
Mr.SA
Posts: 59
Joined: Wed Mar 02, 2016 10:40 am
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L300
Location: Denver

Front skid plates for sale, interested?

Post by Mr.SA »

bigsleep55 wrote:
Mr.SA wrote:If i can get much interest, I'll make another run of these, my friend that was doing them before is unable to now, but i know someone else that will be able to, might just cost me a little more.

After my last run, a few people had trouble mounting them. just be aware that it will take some bending/drilling on your part to fit them. and you NEED the undertray under the engine to mount them to.

If you're interested, post your material preference, steel or aluminum, and auto or manual trans. If i get a lot of interest in aluminum i'll do some, otherwise they'll be all steel.
I'll give it a couple weeks to guage interest, then make a run based on that. so we're looking at about a month timeframe.

I'm still planning on eventually doing a super strong version, but not until i can find someone that will work with me on building them. and those will cost quite a bit more than these.
How much do these end up costing with shipping to Ca? I'd be Aluminium for Auto. Thanks!
depends on how cheap i can get them cut, and bent. its going to be a little more than before so im guessing around 200-250 for steel. I havent done aluminum yet but i'm guessing it'll add another 100 to that.
Post Reply

Return to “Delica Modifications”