Cheap L300 torsion bar upgrade

Mitsubishi Delica Camper vans, lift kits & other Delica Accessories!

Moderator: BCDelica

User avatar
Growlerbearnz
Posts: 1728
Joined: Sat Jun 26, 2010 1:58 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica P25W
Location: New Zealand

Cheap L300 torsion bar upgrade

Postby Growlerbearnz » Thu May 03, 2018 2:41 am

After fitting air shocks to the rear of my van, which slightly stiffen the rear suspension, I've been thinking that the front suspension is way too soft.

The Japanese market L300 4WD wagon (P25/35W) has 20mm diameter torsion bars on the front suspension. Light springs like these make for a comfortable ride and good suspension flex offroad, but on the road they're a bit weak. Add some extra weight, and 20 years of sag, and you end up with a van that corners with the stability of a newborn giraffe, and cataclysmic nosedive under braking.

2WD L300s have 22mm torsion bars, which might be a decent upgrade. Dobinsons.com.au make 24mm bars, which are about perfect, but the AU$500 price is a little painful.

You know what else has 24mm torsion bars? A Hyundai H100 van. Like this 1998 one at the wreckers:
IMG_20180426_113847 copy.JPG
IMG_20180426_113847 copy.JPG (209.77 KiB) Viewed 356 times


The H100 is basically an L300 underneath, and the torsion bars are a perfect match... and they only cost $40 from the local wreckers.

IMG_20180503_151859 copy.JPG
IMG_20180503_151859 copy.JPG (113.89 KiB) Viewed 356 times
IMG_20180503_151909 copy.JPG
IMG_20180503_151909 copy.JPG (274.53 KiB) Viewed 356 times


Hyundai part numbers were written on the bars. LH side = 5415043160, RH side = 5416043160.

Hyundai don't fit rubber boots to protect the splines, but it's easy to swap your boots from your old torsion bars to the Hyundai ones. It's about a 45 minute job to swap both bars, and another 15 minutes to set the suspension height.

Results: I think it's just about perfect. It's still a big, floppy 4WD, but it feels a bit more modern to drive. Turn-in is sharper, and the nosedive under braking is less comical. Motorway driving has lost the slight floaty feel and wobble when changing lanes at speed.
Nothing says "poor workmanship" more than wrinkles in the duct tape.

User avatar
Sylquebec
Posts: 25
Joined: Fri Jan 20, 2017 5:08 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: looking for a delica
Location: quebec

L300 torsion bar upgrade

Postby Sylquebec » Fri May 04, 2018 3:26 pm

thanks for the info

Envoyé de mon SM-G950W en utilisant Tapatalk

User avatar
Lapprentis
Posts: 341
Joined: Sat Dec 28, 2013 6:02 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L300 StarWagon 1990
Location: Quebec

Cheap L300 torsion bar upgrade

Postby Lapprentis » Sat May 05, 2018 5:55 am

GOOD FIND ! Any idea of the part number, from which model/year ? There seems to be a few options available: 5416043150, 5415043420, 5415043160. Partsouq seems to have some at less than 100CAN each but none in stock... Also on Alibaba, Chinese made, could it be the same ? Minimum 10 sets order, at less than 15USD a set ???????? (https://www.alibaba.com/product-detail/ ... 25390.html) ! Thanks again.

Lapprentis :M

User avatar
Growlerbearnz
Posts: 1728
Joined: Sat Jun 26, 2010 1:58 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica P25W
Location: New Zealand

Cheap L300 torsion bar upgrade

Postby Growlerbearnz » Sat May 05, 2018 2:56 pm

I wouldn't trust a torsion bar from anyone but a reputable manufacturer- they're the sort of highly stressed component that can fail from one tiny flaw.

Hyundai part numbers were actually written on the bars, which was nice:
LH side = 5415043160
RH side = 5416043160

The H100 I got the bars out of was a 1998.
Nothing says "poor workmanship" more than wrinkles in the duct tape.

User avatar
Lapprentis
Posts: 341
Joined: Sat Dec 28, 2013 6:02 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica L300 StarWagon 1990
Location: Quebec

Cheap L300 torsion bar upgrade

Postby Lapprentis » Sun May 06, 2018 9:11 am

Thanks Growler ! autopartmaster.com seem to be the best option for North American L300 Owners ! Will cost about 1/3 of Dobinson.

Lapprentis :M

Killbert
Posts: 63
Joined: Sun Jun 12, 2016 4:51 am
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 91 Delica Chamonix
Location: US

Cheap L300 torsion bar upgrade

Postby Killbert » Mon Jun 11, 2018 6:55 pm

Genius. Thanks Growler.

K

sk66
Posts: 109
Joined: Thu Oct 06, 2016 3:24 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: '91 Delica L300
Location: Pennsylvania, USA

Cheap L300 torsion bar upgrade

Postby sk66 » Thu Jun 14, 2018 11:10 am

Be aware that the H-100/Grace is also equipped with 20mm torsion bars (i.e. 5415043151)... so make sure you get the right part numbers!




don't ask how I know this.... :?
Steven
1991 L300
Harrisburg, PA

sealica
Posts: 137
Joined: Mon Aug 08, 2016 5:38 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 1992 L300 P35W, White
Location: Vancouver Isle

Cheap L300 torsion bar upgrade

Postby sealica » Wed Jun 20, 2018 3:37 pm

When looking to purchase used torsion bars are there any tests one can conduct to check that they're not worn out already?


Return to “Delica Modifications”

Who is online

Users browsing this forum: No registered users and 5 guests