On board compressor for air shocks.

Mitsubishi Delica Camper vans, lift kits & other Delica Accessories!

Moderator: BCDelica

User avatar
Growlerbearnz
Posts: 1653
Joined: Sat Jun 26, 2010 1:58 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica P25W
Location: New Zealand

On board compressor for air shocks.

Postby Growlerbearnz » Mon May 07, 2018 7:05 pm

I keep forgetting to inflate the air shocks when towing and only notice when I'm on the motorway. Also, when you get to the campsite and unhitch the caravan, it's a pain to air down the shocks for driving around, and then pump them up again when it's time to tow the 'van home.
So here's a fun little project: take a bunch of air fittings and a cheap(ish) 12V compressor, and build an onboard air system for the air shocks. Monroe's awful fittings didn't make it easy, but I got there in the end.

A bunch of random parts from the pneumatic fittings box. Compressor for inflating the shocks, a solenoid valve for deflating. But first, build a box to mount it all in.
Parts.JPG
Parts.JPG (129.28 KiB) Viewed 127 times


Folding stainless is a pain when you have the world's worst sheet metal folder.
fold.JPG
fold.JPG (250.78 KiB) Viewed 127 times


Peeling the plastic protective sheet off is the best bit.
box.JPG
box.JPG (59.32 KiB) Viewed 127 times


All the bits installed in the case, along with some sound deadener because that case was super resonant.
assembles.JPG
assembles.JPG (90.96 KiB) Viewed 127 times


Installed above the gearbox crossmember where it's dry.
installed.JPG
installed.JPG (79.57 KiB) Viewed 127 times


An outlet for pumping up tyres, if needed. The air shocks act as an air tank.
outlet.JPG
outlet.JPG (58.75 KiB) Viewed 127 times


Now the tricky part. Monroe shocks have this stupid, cheap, proprietary connector.
stupidFitting2.JPG
stupidFitting2.JPG (45.64 KiB) Viewed 127 times


Beneath the stupid Monroe fitting is a 7/8x20tpi thread- almost an AN or JIC fitting, but without the tapered seat to form an airtight seal. Still, I can make an adapter that'll screw on.
StupidFitting.JPG
StupidFitting.JPG (50.37 KiB) Viewed 127 times


Adapters made from a chunk of aluminium. 7/8"x20 threads on one end, 1/8NPT on the other (with 4mm push-in fitting installed)
adapters.JPG
adapters.JPG (68.18 KiB) Viewed 127 times


Adapters installed. Threads sealed with anaerobic thread sealant.
AdapterInstalled.JPG
AdapterInstalled.JPG (104.58 KiB) Viewed 127 times


Dashboard control- a modified tailgate lock/unlock switch and a moderately accurate pressure gauge. Green is 20-90psi, the range the shocks are happy with for long-term use. They'll go to 150psi for short periods.
dash.JPG
dash.JPG (72.39 KiB) Viewed 127 times


Now I can do the lowrider hopping up and down thing- as long as you film it on timelapse. It takes about 30 seconds to go from 20 to 90psi.
Nothing says "poor workmanship" more than wrinkles in the duct tape.

User avatar
lrp374
Posts: 858
Joined: Sun Nov 23, 2008 9:56 pm
Vehicle: 91 Super Exceed
Location: Kamloops

On board compressor for air shocks.

Postby lrp374 » Mon May 07, 2018 7:41 pm

Just when I thought you'd run out of projects!! :-D

User avatar
Growlerbearnz
Posts: 1653
Joined: Sat Jun 26, 2010 1:58 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica P25W
Location: New Zealand

On board compressor for air shocks.

Postby Growlerbearnz » Mon May 07, 2018 10:55 pm

Never finished. While I had the dashboard apart I also modified the wiring loom so the tailgate locks and unlocks with all the other doors, the park lights come on when the ignition is on (as Daytime Running Lights), the horn runs through a relay (so I can add an air horn later), and my lambda/O2 gauge turns on with the ignition rather than with accessories (it wastes a lot of power if the engine's not running).

Oh and tightened one of the pivot bolts on the steering column adjust mechanism, that was causing a vague feeling in the steering by letting the steering wheel move ever so slightly. Whee!

The next job is to repair and paint the tailgate, which has a touch of rust starting behind the windscreen rubber. But of course I'm not going to just fix it, I'm going to modify it to suit my swing-out tyre carrier (delete the numberplate recess) and stiffen it internally (I dislike how flexible the standard tailgate is). I have a spare tailgate stored... somewhere...
Nothing says "poor workmanship" more than wrinkles in the duct tape.


Return to “Delica Modifications”

Who is online

Users browsing this forum: No registered users and 2 guests