Search found 175 matches

by CVI
Tue Mar 27, 2012 6:47 am
Forum: L300 Technical
Topic: Torsion Bar Adjustment / Custom Socket
Replies: 9
Views: 1092

Re: Torsion Bar Adjustment / Custom Socket

best way to adjust those torsion bars is to lift the front tires to release the tension of the torsion bars and it will make wrenching or socketing way easier....don't forget to do alignment after. :-D
by CVI
Mon Mar 05, 2012 6:37 pm
Forum: L400 Technical
Topic: Injector Exchange
Replies: 83
Views: 12105

Re: Injector Exchange

Just to help out in this discussion. Our Diesel Calibration workshop in Manila doesn't recommend changing or altering injector nozzles with a different specification other than the original specs and type of injector recommended by the manufacturer. Here are a few differences on specs between the tw...
by CVI
Mon Mar 05, 2012 4:21 pm
Forum: L400 Technical
Topic: Injector Exchange
Replies: 83
Views: 12105

Re: Injector Exchange

Hi Steven,

Just a clarification, Is it a 4D56 Hyundai injectors or what, may I ask, are you installing on the 4M40 engine ??

Thanks and best regards,
Butch
by CVI
Thu Jan 12, 2012 10:21 pm
Forum: L400 Technical
Topic: Trouble shifting into 4WD C/D light flashing
Replies: 4
Views: 1009

Re: Trouble shifting into 4WD C/D light flashing

Hi... trouble with the vac solenoid switch actuating the 4WD circuit. You may need to replace them to solve that issue.
by CVI
Sun Jan 08, 2012 8:01 pm
Forum: General Discussion
Topic: Question about CVI, Where's Butch??
Replies: 12
Views: 1248

Re: Question about CVI, Where's Butch??

I'm so sorry for the inconvenience guys... Happy New Year to all!

I'm back to work .... Mondays to Fridays @ 0930to1830 workshop hrs. 604-710-7000 24hrs (emergency calls) :-)

Butch
by CVI
Fri Nov 04, 2011 8:00 am
Forum: Events - BC Lower Mainland
Topic: Pajero Meet! *November 18th IKEA Coquitlam 7pm*
Replies: 43
Views: 6956

Re: Pajero Meet! *November 18th IKEA Coquitlam 7pm*

Count me in! Will bring Gerri... :-)
by CVI
Tue Nov 01, 2011 6:40 am
Forum: Events - BC Lower Mainland
Topic: Delica Occupy IKEA Meet! *November 18th IKEA Coquitlam 7pm*
Replies: 55
Views: 9080

Count me in too .
by CVI
Mon Aug 29, 2011 3:45 pm
Forum: L400 Technical
Topic: Heater flow valve
Replies: 3
Views: 583

Re: Heater flow valve

jfarsang is right. Is your L400 a super exceed one where the climate control is electronic? If it is... then there is an actuator that's causing the problem. It's most likely burnt out and not closing the flap as required by your temperature setting. It is located on the center console below the rad...
by CVI
Mon Aug 29, 2011 3:40 pm
Forum: L300 Technical
Topic: fuel system leak
Replies: 31
Views: 3489

Re: fuel system leak

Leaky injectors will contribute and cause that similar issues as well. We've found some cases where the injector nozzles are not holding pressure and will cause that problem on the high pressure side. When you prime your fuel system using the hand primer on top of the fuel filter housing, it should ...
by CVI
Mon Aug 29, 2011 3:30 pm
Forum: Site Suggestions & General Feedback
Topic: A New Technical Section.
Replies: 8
Views: 4505

Re: A New Technical Section.

Hey!

Splendid Falco!! That will work! A "how to" or "DIY" section can consolidate all similar issues and cut down redundancy. It'll make it even easier for us to respond to certain issues which can help our community :-D
by CVI
Mon Aug 01, 2011 6:23 am
Forum: Mitsubishi Vanwagon
Topic: Maintenance Light Reset?
Replies: 11
Views: 2597

Re: Maintenance Light Reset?

Hi!

It could mean an engine fault code is present too. Big possibility it's an emission related problem. You can bring it to a basic garage and have them hook up a basic fault code reader to check what code came on...

Good luck,
Butch
by CVI
Fri Jul 22, 2011 12:58 pm
Forum: L400 Technical
Topic: Van trouble in Calgary
Replies: 26
Views: 3059

Re: Van trouble in Calgary

Hi Patton... Mardy is right! There is a small vac hose on the left hand side of your engine connected to the egr. All you need to do is to remove that hose from your egr and plug it. That's it. There is a vac solenoid actuating the egr valve and that is apparently malfunctioning. That will cause all...

Go to advanced search